Designed & hand built at Chem-X. The Real Deal Kit is the optimal way to apply our touchless wash, Stars + Stripes. Completely plug & play and compatible with almost any power washer. This kit solves the common problems found with 2-step touchless soaps & equipment. The Real Deal is made with rock solid, stainless steel components and comes with our safest and most effective touchless wash ever. It's a no brainer, this is the easiest way to save money and time in your wash bay.
Suttner ST-164 Touchless Foam Injector
44" Chem-X Foam Lance (Built Complete)
2 Gallons Stars + 2 Gallons Stripes. Super Concentrated
DUAL FOAMING CHEMICAL INJECTOR
The most efficient and durable foam injector available, with a dilution range from 12:1 to 200:1. The easiest way to select between two chemicals and rinse. Simply switch lever on the top of the injector to the desired position(chem 1 or chem 2) and let the soap fly.
Metering tips control the soap's draw rate. The dosing nozzles have a pin sized hole the soap is drawn though, the size of this hole determines your soap to water ratio. Suttner foaming Injectors arrive with the correct dosing nozzles already installed. The dosing nozzles offer a dilution range from 12:1 to 200:1.
CHEM-X FOAM LANCE
Change between rinse and foam directly at the gun. Simply release trigger and twist The Suttner ST-58 Change Over Valve to either rinse or foam. The Chem-X Foam Lance screams quality and durability. Built with as much stainless steel as possible and designed to be very easy to use. By far the best foam lance on the market! MORE INFO HERE.
Suttner ST-75s Foaming Nozzle
SuttnerST-58 Change over Valve
Suttner ST-2305 Trigger
Mosmatic DGV Swivel
2 GALLON STARS + 2 GALLON STRIPES
SUTTNER 10' HOSE
POWERWASHER TO INJECTOR
10' Suttner Hose / 6,000 PSI / Abrasion Resistant
3/8" Quick Connect Plug
3/8" Quick Connect Coupling
DIRECTIONS PANNEL + SPARE PARTS
Direction Panel 10"x15" (include 3M double sided tape) + Spare Parts
Replacement ST-75s Foamer
(2 PACKS) 18 metering/dosing nozzles, each chemical can be set at individual desired strengths
Replacement Foam Agitator Pad + O-Ring for ST-75s Foamer
(3) Rubber Cushioned Hose Clamps
SEE IT IN ACTION!
HOW TO INSTALL
1. INSTALL ST-164 INJECTOR ONTO WALL (or MACHINE)
Mount Injector on wall/machine using the provided mounting bracket, with in 10' of power washer.*If you would like the Injector further away or closer to your power washer please call Chem-X with the preferred hose length.
2. CONNECT POWER WASHER TO INJECTOR
Using the provided 10' jumper hose. Attach 3/8" quick connect plug from jumper hose to power washer outlet. Attach 3/8" quick connect coupler from jumper hose to inlet on ST-164
3. CONNECT INJECTOR TO POWER WASHER HOSE
Plug in your existing power washer hose(or hose reel connector hose) into outlet/bottom of the ST-164..
4. CONNECT POWER WASHER HOSE TO GUN
Plug your power washer hose into the spray gun using the quick connect plug or hard pipe hose directly into Mosmatic DGV Inline Swivel.
5. INSERT PICK UP TUBES INTO SOAPS
Place the left side tube in Stars(BLUE)and right side inStripes(RED).
-Injector will be set to run at 100:1 unless specified otherwise, this can be changed by simply changing metering tip inside injector barbs.
-If using a hot water machine, scale build up can clog the foam nozzle on the lance. On start up always run lance in rinse mode for about 30-60 secondsto flush out any debris through the rinse nozzle. For systems that see frequent clogs due to coil scale/debris we offer this ST-75 Foam Nozzlewhich is less likely to clog and can be rinsed.
Figure out Your current rinse nozzle size
Use the chart below to figure out your nozzle size. You will need your power washer's current GPM and PSI. This information is usually found on a sticker located on your machine.
ST-164/ST-160 Dosing Nozzle RATIO + PERCENTAGE Chart
The chart below shows dosing nozzle size (opening) and the percentage of draw when the chemical used has the same viscosity as water.
CHEM-X FOAM LANCE
Stainless steel components
Min/Max Flow Rate: 1-6gpm
Min/Max PSI: 1000-4000 PSI
Max Temp: 212 degree *Recommended temp is 125-130 degrees
Adjustable vented grip
SUTTNER ST-2305 SHUT OFF GUN
The easy pull trigger reduces trigger pulling force by 60% compared to other spray guns
Proper spray angle for optimal positioning of pressure points
Max PSI: 5000 PSI
Max Flow Rate: 12 GPM
SUTTNER ST-164 DUAL CHEMICAL INJECTOR
Max hose length after injector: 150'
Integrated lever that allows you to easily switch from Stars to Stripes
Durable stainless steel housing
18 metering/dosing nozzles, each chemical can be set at individual desired strengths(comes pre set to run 100:1)
Min/Max Flow Rate: 1-18 GPM
Min/Max PSI: 1000-5000 PSI
Max Temp: 212 degree
Must be sized according to your current nozzle size. If nozzle size is unknown, please call us with the GPM and PSI of your power washer.