THE REAL DEAL Touchless Foaming Kit

INCLUDES

-

SUTTNER ST-164 DUAL FOAMING CHEMICAL INJECTOR 

The most efficient and durable foam injector available, with a dilution range from 12:1 to 200:1. The easiest way to select between two chemicals and rinse. Simply switch lever on the top of the injector to the desired position(chem 1 or chem 2) and let the soap fly.

--

CHEM-X FOAM LANCE 

The Chem-X Foam Lance was designed and hand built by Chem-X. We took the very best components and pieced them together in a layout with pure functionality and durability in mind. An almost fully stainless lance that is built to hold up in harsh environments. With this lance you can change between foam and rinse directly at the gun. Simply release the trigger and twist The Suttner ST-58 Change Over Valve a quarter turn to either rinse or foam. By far the best foam lance on the market! MORE INFO HERE. 

-

Stars + Stripes Touchless Wash

When Stars+Stripes mix on the vehicle surface, a resulting pH shock will activate the cleaning reaction. This dual stage process breaks the static bond of dirt and road film from the surface, allowing the high psi rinse to remove more grime than any single stage application and also results in a neutral pH. This process saves the user up to 80% of the time it would normally take to do a mitt wash. Using two soaps also lets us tackle more grime by allowing us to use a wider range of surfactants that help with many different types of grime. 

--

SUTTNER 10' HOSE - POWERWASHER TO INJECTOR

-

SEE IT IN ACTION!

HOW TO INSTALL

1. INSTALL ST-164 INJECTOR ONTO WALL (or MACHINE)

Mount Injector on wall/machine using the provided mounting bracket, with in 10' of power washer. *If you would like the Injector further away or closer to your power washer please call Chem-X with the preferred hose length.

2. CONNECT POWER WASHER TO INJECTOR

Using the provided 10' jumper hose. Attach 3/8" quick connect plug from jumper hose to power washer outlet. Attach 3/8" quick connect coupler from jumper hose to inlet on ST-164.

3. CONNECT INJECTOR TO POWER WASHER HOSE

Plug in your existing power washer hose(or hose reel connector hose) into outlet/bottom of the ST-164.

4. CONNECT POWER WASHER HOSE TO GUN

Plug your power washer hose into the spray gun using the quick connect plug or hard pipe hose directly into Mosmatic DGV Inline Swivel.

5. INSERT PICK UP TUBES INTO SOAPS 

Place the left side tube in Stars(BLUE) and right side in Stripes(RED). 

-Injector will be set to run at 100:1 unless specified otherwise, this can be changed by simply changing metering tip inside injector barbs.

-If using a hot water machine, scale build up can clog the foam nozzle on the lance. On start up always run lance in rinse mode for about 30-60 seconds to flush out any debris through the rinse nozzle. For systems that see frequent clogs due to coil scale/debris we offer this  ST-75 Foam Nozzle which is less likely to clog and can be rinsed.-- 

How To Repair Common Issues on Suttner Foam Gear

Specs

CHEM-X FOAM LANCE

• 44" length
• Stainless steel components
• Min/Max Flow Rate: 1-6gpm
• Min/Max PSI: 1000-4000 PSI
• Max Temp: 212 degree  *Recommended temp is 125-130 degrees 
• Adjustable vented grip

SUTTNER ST-2305 SHUT OFF GUN

• The easy pull trigger reduces trigger pulling force by 60% compared to other spray guns
• Proper spray angle for optimal positioning of pressure points
  
• Max PSI: 5000 PSI
• Max Flow Rate: 12 GPM

SUTTNER ST-164 DUAL CHEMICAL INJECTOR

• Max hose length after injector: 150'
• Integrated lever that allows you to easily switch from Stars to Stripes
• Durable stainless steel housing
• 18 metering/dosing nozzles, each chemical can be set at individual desired strengths(comes pre set to run 100:1)
• Min/Max Flow Rate: 1-18 GPM
• Min/Max PSI: 1000-5000 PSI
• Max Temp: 212 degree